R8 Bradley EXO | Attachment | 6-Post

R8 Bradley EXO | Attachment | 6-Post

• Modular EXO cable pulley system with 49 angle combinations for maximum training freedom
• Attachment for existing R8 Power Racks – expansion without conversion
• Available in three crossbar depths: 16.5", 30.5" and 43"
• Choose from three cable pulley systems: 380 lb, 500 lb or Plate Loaded
• For 6-post racks in positions 4 to 6 – the weight stacks are installed in the rear section

Two EXO Arms. 49 angles. No limits.

• Horizontal adjustment: 180° in 7 positions, vertical adjustment: 90° in 7 positions
• A total of 49 angle combinations per side
• Ideal for cable flys, rows, lat pulldowns, face pulls, curls, triceps pushdowns and functional training
• Turns a fixed cable pulley point into a freely adjustable cable-cross system

The cable pulley follows your movement – not the other way around.

• 360° rotatable cable outlet for a clean cable path in the pulling direction
• No jamming, no rubbing on the frame
• Even power transmission and a natural training feel across the entire range of motion

Three cable pulley systems. Your choice.

• 380 lb weight stacks (2 × 190 lb) – long cable travel for expansive core exercises and wide ranges of motion, magnetic pin for lightning-fast repinning
• 500 lb weight stacks (2 × 250 lb) – heavy cable training despite the 2:1 ratio
• Plate Loaded – load flexibly with your own weight plates, no limit set by a fixed weight stack

Weight to the back. Freedom to the front.

• The complete cable pulley including weight stacks sits in the rear section of your 6-post rack
• The front rack section stays clear – full freedom of movement for squats, bench press and rack training
• Room at the front for further attachments or a retrofittable Smith Machine

Rock-solid at the rack. Freely movable when adjusting.

• Trolley runs with zero play on the upright – no wobbling, no rattling, no giving way
• Under training load, the arm locks into the force vector
• Tool-free adjustment, rack coating protected by UHMW plates
• Designed for 3"x3" uprights

2:1 ratio. Controlled. Joint-friendly.

• Even resistance, finer weight increments and clean technique even during heavy sets

The upgrade your gym deserves.

• Compatible with R8 attachments like step-up platform, hip-thrust pad, leg blocker and dip station
• Simultaneous use of both cable pulley sides possible with an optional dual pull bar
• With 6-post racks, compatible with a retrofittable Smith Machine – with the cable pulley at the rear, there is room for the Smith Machine at the front, and vice versa
• TÜV- and GS-certified according to EN 20957 – suitable for commercial gyms

Which position is right for you?
The right choice depends on three factors: your weight system, the crossbar depth of your front rack section and the depth of your rear section.

Step 1 – What kind of rear section do you have?
The depth of your rear section determines which positions are available to you:

• 16.5" rear section → position 4 only
• 30.5" rear section → position 4 (front) or position 5 (rear)
• 43" rear section → position 4 (front), position 5 (middle) or position 6 (rear)

Step 2 – Where is each position?
Read the other way around:

• Position 4 → 16.5" rear section (only position), front of a 30.5" or 43" rear section
• Position 5 → rear of a 30.5" rear section or middle of a 43" rear section
• Position 6 → rear of a 43" rear section

Step 3 – Choose your cable pulley system, crossbar and position in the configurator.
The crossbar selection (16.5", 30.5" or 43") refers to the depth of your front rack section – not the rear section.
Some combinations of crossbar and position share one variant because the cable and mechanics are identical. Select your combination and you will automatically land on the right product. The matching cable is included depending on the position.

Do you have a 4-post rack? Then the R8 Bradley EXO | Attachment (positions 1–3) is the right product for you.